So I decided my 2002 Ducati ST4s Needed some mods here and there... soooooo...

Mods I already had done to the duke...

or Phase One Mods

Aftermarket clutch slave cylinder. (to be upgraded to KBike)
Heated Hand Grips.
Ventura Pack Rack.
Tank re-sealed from within. (Sorry can not remember the name of the resin used.
Aftermarket ECU. (no longer requires a master red key)
MotoElectrical starter kit, new earth wire, cables and brushes for starter motor etc.
Half debaffled stock mufflers. (To be upgraded to GPR Furore Black)
GPS RAM arm for Garmin.
Jumper wire to the battery under the seat.

So after the Ducati came back from the doctors after being knocked over while parked at work. (Yes an insurance claim) She got a new nose fairing and painted, and she had a quick touch up on the lower fairing and looking very pretty and tidy. So I decided to a few mods. Nothing major to the engine mainly cosmetic. (but she is in need of a bath... and a polish which lets be honest I dislike doing... I am to busy riding her.)

So the below cost's does not include any shipping & handling costs and only shows unit cost, and all in NZD including GST.

Current Mod Project
Phase Two Mods

So even though I have said phase one, two and three etc, I could easily bring forward any part and or accessories into phase two... I am only breaking it into phases so I don't do it all at once and bust the bank... Currently in phase three/four. After this is all done... will I keep the bike? That I can not answer.

Anyhow the first thing I did was get the seat recovered by Lewis at Tinwald Canvas and Upholstery, and the result is awesome, he did a great job and was a pretty fast turn around. I just showed a few pictures online and said I like this but maybe in grey... he did an awesome job and already has spruced the old girl up.

Seat recovered

Seat recovered, new red anodised clutch pressure plate and bolts, and carbon fibre clutch cover, red anodised fairing bolts, and brake and clutch lever. red anodise brake, clutch and oil filler cap reservoir. GPR Furore Matt Black Mufflers, carbon fibre fuel cap flange, red anodise fuel cap, carbon fibre heel guards. Carbon fibre ignition key cover. New carbon fibre look, anti-scratch tank guard.

Cost:	Seat re-covered	$180.00
Status:	Installed
Tools Required:	Someone that knows how to do upholstery...

Clutch upgrade

The next mod I did was the clutch, I went to Kev at MotoXtreme here in Dunedin (who has been nothing but helpful through-out the insurance claim) and has been my goto shop for all the other issues I have had with the Ducati.

I said to Kev I want a fancy looking clutch he said: "OK, what colour pressure plate?" I answered "Red" and that was basically the conversation. So basically I don't know what brand he is getting... I got and have a carbon fibre clutch cover from CarbonWorks.

HDESA USA Racing Clutch

Cost:	Clutch pressure plate with red springs.	$300.00
	Clutch basket.	$150.00
	Clutch fibre plates.	$205.00
	Carbon fibre clutch cover.	$123.73
Status:	Installed
Tools Required:

Front Sprocket Guard

Keeping with the carbon fibre theme, I have carbon fibre heel guards. A carbon fibre front sprocket cover from CarbonWorks is currently waiting on stock.

Cost:	Carbon fibre front sprocket cover.	$114.00
Status:	Installed
Tools Required:	Allan key. I did have to do a small modification to the shape to make it fit.

Heel Guards

Carbon fibre heel guards from Amazon

Cost:	Carbon fibre heel guards.	$93.65
Status:	Installed
Tools Required:	8mm Socket

GPR Black Furore Mufflers

I ordered some GPR mufflers from Italy. This will give a different sound and give a more modern look on a 17 year old bike. I bought these via an overseas seller on Trademe who used UPS and was also the broker for customs clearance which made the whole process pretty easy and painless.

Dual homologated FURORE Nero Exhaust System (Muffler) kit with removable db killer (baffle) for racing use;

Lightweight (see measurements below).
Includes link pipe and full system, brackets, holder and fasteners. Link pipe is included only when necessary. All mounting hardware included for a perfect fitment.
No need to cut anything to install this exhaust
Link pipe stainless steel made (Aisi 304) and caps ERGAL made by CNC machinery
Furore silencer made from Aluminum sealed sleeve.
Made in Italy.
Produced under European directives
Street legal.
2 year international warranty.
Successful in sound and performance.
Produced using hand made craftsmanship and advanced TIG welding.

Measurements:

Diameter: 90x120 mm
Approximate weight of 3.86 pounds (1.75 kg)

Cost:	Furore GPR Mufflers. (Black)	$918.75
	Import charges & GST.	$196.00
Status:	Installed
Tools Required:	Allan Key, Spring hook

Adjustable Brake & Clutch Levers

I have some adjustable brake and clutch levers (short). Now I have only bought a cheap set here as I may not like them, however, if I do, I will get a decent set. I bought them off Trademe

Cost:	Adjustable clutch & brake levers. (Red)	$69.90
Status:	Installed
Tools Required:

Fluid reservoir caps

So just to spruce up the old girl I added to the cart using the add to cart button and bought some new KBike brake & clutch reservoir caps as well as oil filler cap from Black-Label. Just by adding these that have added colour and a new look.

Cost:	KBike Clutch reservoir caps. (Red)	$89.54
	KBike Oil cap. (Red)	$25.95
Bought from:	https://black-label-meccanica.myshopify.com
Status:	Installed
Tools Required:	Philips Screw Driver

Fairing bolt kit.

So again I said to Kev at MotoXtreme "Can you get me some red fairing bolts?" and he said "ok..." it was short and simple but that just how we roll.

Cost:	Fairing bolt kit. (RED)	$99.00
Status:	Installed
Tools Required:	Hex/Allen Key

Tank Pad Protector

So the final item on in phase two of mods is a new tank pad guard, and again I went to MotoXtreme and said... well you get the idea ...

Cost:	Tank pad protector	$25.00
Status:	Installed
Tools Required:

Phase Three Mods

Carbon Fibre Key Chain Guard

This carbon fibre keychain tank guard is a simple exchange of the stock plastic one, and adding more carbon fibre look over the old girl... BTW she does say she is enjoying the attention... wait what?

Cost:	Carbon fibre key chain guard	$204.05
Status:	Installed
Tools Required:	Star/Allan Key

Cost:	Carbon fibre key ignition cover	$131.65
Status:	Installed
Tools Required:	10mm socket/Spanner. Screw driver to pry out key sensor and wiring.

KBike timing inspection cover.

Adding more colour to the engine with a red anodised timing inspection cover.

Cost:	KBike timing inspection cover	$41.51
Bought From:	https://black-label-meccanica.myshopify.com
Status:	Installed
Tools Required:	Hex/Allan Key

New KBike clutch slave cylinder

Although I already have an aftermarket one I am replacing it with a new KBike red anodised adding the colour. And this is supposed to be a better slave cylinder.

Cost:	KBike clutch slave cylinder	$148.43
Bought From:	https://black-label-meccanica.myshopify.com
Status:	Installed
Tools Required:	Hex/Allan Key

KBike Handle Bar Ends

A quick and simple colour add is some bar ends, red anodised as the rest. However, as I have not decided on bar end mirrors or lever guards I am only class this quick colour change mod as temporary.

Cost:	Handle Bar Ends	$41.51
Bought From:	https://black-label-meccanica.myshopify.com
Status:	Not going to be installed. So I received them and install one of them and then decided I prefer them to be black.
Tools Required:	Hex/Allan Key

CNC Racing carbon fibre gas cap flange & CNC Racing red anodised cap (with key)

Cost:	CNC Racing carbon fibre flange	$247.50
	CNC Racing red anodised fuel cap	$73.51
Status:	Installed
Tools Required:	Hex/Allan Key

CNC Racing Reservoir Mounting Screws

Cost:	CNC Racing reservoir mounting screws	$17.80
Status:	Installed
Tools Required:	Hex/Allan Key

Ducabike Frame Plug Kit

Cost:	Ducabike Frame Plug Kit	$59.05
Status:	Installed
Tools Required:	Hex/Allan Key

CNC Racing steering head plug

Cost:	CNC Racing Steering Head Nut	$59.05
Status:	Installed
Tools Required:

Future Mods I am looking into
Phase four

Carbon Fibre Inner Dash

Cost:	Carbon Fibre Inner Dash	$268.57
Status:	Waiting to be ordered
Tools Required:	Hex/Allan Key

Cost:	Carbon Fibre Side Fairing Air Intakes	$471.27
Status:	Waiting to be ordered
Tools Required:	Hex/Allan Key

Brembo Master cylinder clamp no Mirror Mount

OEM and RCS Brembo brake and clutch master cylinder clamp without mirror threats made in light alloy, machined from solid and then anodized. Kit is composed by one clamp, Two black finished galvanized screws are included. I think this is a bit step for what it is... but

Cost:	x2 Master cylinder clamp	$74.42 each
Status:	Installed
	https://www.cncracing.com/en/product/brembo-master-cylinder-clamp-no-mirror-mount.html
Tools Required:	Hex/Allan Key

Oil Breather valve

Cost:	Master cylinder clamp	$76.28
Status:	Installed
	https://www.cncracing.com/en/product/breather-valve-ducati.html
Tools Required:

CNC Racing billet bleed valve cover kit for Brembo

Cost:	Bleed valve kit	$57.67
Status:	Waiting to be ordered
	https://www.cncracing.com/en/ducati_sport-touring_st4_2002/universal-billet-bleed-valve-cover-kit-for-brembo.html
Tools Required:

Phase four upgrades may not be done for a while as I have to recover some funds from phase two & three

Zero Gravity windscreen

Cost:	Zero Gravity Windshield	$147.72
Status:	Waiting to be ordered
Tools Required:	Hex/Allan Key

Waterpump guard

Cost:	Water pump guard	$87.76
Status:	Installed
Tools Required:	Hex/Allan Key

New Starter Motor.

Cost:	Starter Motor
Status:	Waiting to be ordered
Tools Required:

Lithium Battery.

Cost:	Lithium Battery
Status:	Waiting to be ordered
Tools Required:	Hex/Allan Key, spanner, screw drievr

K&N Air Filter.

Cost:	K&N Filter
Status:	Waiting to be ordered
Tools Required:

New rider and pillion foot pegs.

Cost:		Rider & pillion pegs
Status:		Waiting to be ordered
Tools Required:

Intergrated indicators and bar end mirrors and handle bar ends
These I am not to sure on... I have to think about it as it replaces the bar ends.

Cost:		Bar end mirrors
Status:		Waiting to be ordered
Tools Required:

The other option is lever guards I have not decided...

Cost:		Lever guards
Status:		Waiting to be ordered
Tools Required:

Phase five Mods

Braided brake lines.

Front brake lines

Cost:	Braided brake lines	$92.43
Status:	Waiting to be ordered
Tools Required:

Rear brake line

Cost:	Braided brake lines	$49.90
Status:	Waiting to be ordered
Tools Required:

New brake discs.

Cost:		New brake disc's
Status:		Waiting to be ordered
Tools Required:

Givi top box.

Cost:		Givi Top box
Status:		Waiting to be ordered
Tools Required:

Silcone Radiator Hoses

Cost:	Silcone Radiator Hoses	$129.00
Status:	Waiting to be ordered
Tools Required:

Stock Side Saddles and other parts painted.

So I want the side saddles either repainted or vinyl wrapped and made to look all pretty (If vinyl wrapped will be in carbon fibre look). The other parts include but not limited to; sizzy bar, rear seat fairing, and side saddles.

Cost:		Repaint sided saddles
Cost:		Vinyl wrap sizzy bar
Status:		Getting qutoes
Tools Required:

The one mod I would love to do is get my hands on a Ducati Designs aftermarket headlight system for the ST2/4/s but unfortunately he no longer makes them and they are like hens teeth to get hold of. Being in NZ very very rear I have only seen one ST4 with this mod done to it here in NZ (I am sure there are more) however they are rarer than hens teeth to find.

Running total spent

Parts:	$3478.03
Mechanic:	$665.88
Total:	$4118,03

The Ducati is getting some Mods